|
#1
| ||||
| ||||
| Ever fall in? Ever ford a stream? Ever take the old girl fishing? If you answered yes to any of these...you may want to look at waterproofing your rounds. It is really simple. 1. Get some thin (really runny) nail polish. (the thinner the better stay away from anything metallic or pearled) 2. Wipe off the primer area of each round with a q-tip dipped in alcohol (not saturated and let dry thoroughly). 3. Brush a very small amount of nail polish around the primer seam (let dry thoroughly). 4. Wipe off the seam area at the case mouth/bullet with a q-tip dipped in alcohol (not saturated and let dry thoroughly). 5. Brush a very small amount of nail polish around the case mouth/bullet seam (let dry thoroughly). 6. Load and carry. This is not perfect. No system is but it is better than nothing and it works. I learned it from examining Russian Makarov rounds and looking at failure rates due to water/oil intrusion into primer areas. I have done this to all my pistol rounds and have not had a failure to ignite in the last couple of thousand rounds (since I have started this) PS if it's STUPID but it works...it ain't STUPID!!!:Smilie Funny: Keep you powder dry and you gun ready!:57:
__________________ FESTUS IN OMNIA PARATUS A bitter American clinging to God and Guns Last edited by festus; 05-17-2008 at 12:27 PM. Reason: spelling |
|
#2
| ||||
| ||||
| Sounds like a good idea. The only problem I see is after shooting a good amount, your gun will be gummed up with nail polish. I can just see my friends making fun of me for putting make-up on my ammo.:2:
__________________ It's ironic, we fight for our right to bear arms for our defence, but pray we never have to use them for that. |
|
#3
| |||
| | |||
| I read something about doing this a few years ago but have never tried it. Thanks for the reminder. I may do a few and try them.
__________________ To disarm the people (is) the best and most effectual way to enslave them...” George Mason By faith Noah, being warned of God of things not seen as yet, moved with fear, prepared an ark to the saving of his house; by the which he condemned the world, and became heir of the righteousness which is by faith. Hebrews 11:7 |
|
#4
| ||||
| | ||||
| I've heard of people recovering ammo from under water after some time and it shooting fine. I've never heard of anyone getting wet while hunting (from rain or falling into water) and having a failure to fire. While I am sure your tip will provide some added protection, I doubt it's really needed. I have shot a lot of the coated ammo available from the cheaper brands and think it adds to cleaning time. I guess if it makes you feel more secure there's nothing stopping you.
__________________ When I was a boy I was told that anybody could become President; I'm beginning to believe it. --Clarence Darrow Words to live by: Ecclesiastes 10:19 America's best Xtian: http://www.bettybowers.com/ |
|
#5
| ||||
| | ||||
| I carred shotgun slugs in light vasaline coat when diving of Florida. |
|
#6
| ||||
| ||||
| There was a NYC subway cop that suffered a failure to ignite because some CLP weeped between the primer and case and killed the primer. this helps prevent that as well. In any case I am looking at stuff I carry not range fodder. I have to know that when it's time every thing will work as advertised. anything less than 100% reliability is unacceptable. I might be anal retentive about it but my equipment all works first time every time (except for that one PROMAG in a previous post). When I discover a piece of gear I can no longer trust my life to...IT GOES BYE-BYE!!!!!
__________________ FESTUS IN OMNIA PARATUS A bitter American clinging to God and Guns |
|
#7
| ||||
| ||||
| Most ammo is very well sealed and is waterproof for normal contact with water. Myself, I wouldn't put anything on a round to make it waterproof. I've carried ammo that was underwater for several hours and didn't have any failures to fire. There have been several test shown on TV where rifles and pistols were fired underwater to see what would happen. None of those had any misfires. Moisture is only a factor if it's stored in a humid or wet condition. Corrosion of the brass will cause case failures and chances of overpressure from the contaminated powder. Just store your ammo in a clean dry condition and don't worry about your carry ammo.
__________________ USAF Retired, CATM ie: Red Hat SC CWP, NR NH CWP NRA life member Hard things are put in our way, not to stop us, but to call out our courage and strength. To preserve liberty, it is essential that the whole body of people always possess arms, and be taught alike, especially when young, how to use them... -- Richard Henry Lee, 1787 |
|
#8
| ||||
| | ||||
|
__________________ ![]() "When Government fears the people, it's liberty. When people fear the Government, it's tyranny." - Benjamin Franklin "It is better to die on one's feet than to live on one's knees." - Albert Camus "The two enemies of the people are criminals and government, so let us tie the second down with the chains of the constitution so the second will not become the legalized version of the first." - Thomas Jefferson |
|
#9
| ||||
| ||||
| Thanks for that. I will quit being quite as paranoid but will probably still seal my primers anyway.:y:
__________________ FESTUS IN OMNIA PARATUS A bitter American clinging to God and Guns |
|
#10
| ||||
| ||||
| After seeing the way he prepared those primers, it is apparent that he may have used TOO much oil. I tried some shot-gun primers and had disasterous results with liquid wrench and with KROIL. about 1/4 of the primers were dead. NOT GOOD. I then started doing some homework about Russian ammo MFG. They seal avery primer because they know that if there is a way for a GI to screw it up, He will. Seems we can also learn from our NATO partners...Every 7.62 NATO round I own from other that the USA is primer sealed. If it is not such a good Idea, Why do the worlds Armies use it?:22:
__________________ FESTUS IN OMNIA PARATUS A bitter American clinging to God and Guns |
![]() |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
| |