S&W Model 66-2 .357 Combat Magnum issue
Page 1 of 2 12 LastLast
Results 1 to 10 of 16

Thread: S&W Model 66-2 .357 Combat Magnum issue

  1. #1

    S&W Model 66-2 .357 Combat Magnum issue

    When firing my S&W Model 66-2 using .357mag ammo, the cylinder will jam and not cycle to the next round. However, if I shoot .38spl or .38+P, it cycles just fine with no issues whatsoever. Anyone here had any issues like this? And of so, what was the fix?

    Thanks.
    S&W Model 66-2 .357 Combat Magnum issue-s-w-model-66-2.jpg
    SI VIS PACEM, PARA BELLUM !!
    (If you wish for peace, prepare for war !!)

  2. Sounds like a pressure issue. I recently read an article on that very model that said to use only 158 gr loads. Something about the forcing cone? It also said that's why they don't make the K frame .357. Have you tried the heavier loads?

  3. #3

    Gas ring expanding...?

    This might shed some light:

    Is there a "best" S&W model 66 version? - THR

    I'm no gunsmith...but this sounds like the problem you're having.

    I bet if you sent it in to Smith & Wesson, they'd fix it for you for nothing.
    S&W M&P 45; Ruger GP100 .357 Magnum; Charter Arms .38 Undercover
    http://www.usacarry.com/forums/members/phillip-gain-albums-phil-s-photos-picture3828-reciprocity-map-29jun11.JPG

  4. #4
    Join Date
    Dec 2011
    Location
    Hillsborough,FL 6 & 6 Upstate New York
    Posts
    33
    Quote Originally Posted by BKG203 View Post
    When firing my S&W Model 66-2 using .357mag ammo, the cylinder will jam and not cycle to the next round. However, if I shoot .38spl or .38+P, it cycles just fine with no issues whatsoever. Anyone here had any issues like this? And of so, what was the fix?

    Thanks.
    S&W Model 66-2 .357 Combat Magnum issue-s-w-model-66-2.jpg
    I have a 686, and shoot .38's in it almost all the time. When I go to shoot .357's, they don't drop all the way into the cylinder, because there is a carbon build up where the .38 bullet leaves the cylinder. This maybe your problem. It's very hard to clean this out and this is why it's jamming, at least with my gun!

  5. Don't know if this is related but, had a S&W "scandium" .357 mag that used to hang up after 3 or 4 shots. Seems the bullets were extracting them selves from the cartridge as I was shooting. Could hardly ever make it to the 5th round! Had to look for ammo that was very well swedged so the bullet wouldn't "self extract". I got rid of it.
    Ron

  6. #6
    Quote Originally Posted by SingleAction View Post
    I have a 686, and shoot .38's in it almost all the time. When I go to shoot .357's, they don't drop all the way into the cylinder, because there is a carbon build up where the .38 bullet leaves the cylinder. This maybe your problem. It's very hard to clean this out and this is why it's jamming, at least with my gun!
    Thanks, but build-up is not a problem. This gun is impeccably clean and the .357's drop all the way into the cylinder.
    SI VIS PACEM, PARA BELLUM !!
    (If you wish for peace, prepare for war !!)

  7. #7
    Quote Originally Posted by cmj0968 View Post
    Sounds like a pressure issue. I recently read an article on that very model that said to use only 158 gr loads. Something about the forcing cone? It also said that's why they don't make the K frame .357. Have you tried the heavier loads?
    Thanks. I am using 158gr SJHP's.
    SI VIS PACEM, PARA BELLUM !!
    (If you wish for peace, prepare for war !!)

  8. #8
    Quote Originally Posted by Phillip Gain View Post
    This might shed some light:

    Is there a "best" S&W model 66 version? - THR

    I'm no gunsmith...but this sounds like the problem you're having.

    I bet if you sent it in to Smith & Wesson, they'd fix it for you for nothing.
    Thanks. I could possibly be the gas ring expanding, but it does it when it is first fired with .357's (gun is cold).

    I think I am going to contact S&W and talk to a rep. Thanks for all the responses and suggestions from everyone.
    SI VIS PACEM, PARA BELLUM !!
    (If you wish for peace, prepare for war !!)

  9. #9
    Quote Originally Posted by SingleAction View Post
    I have a 686, and shoot .38's in it almost all the time. When I go to shoot .357's, they don't drop all the way into the cylinder, because there is a carbon build up where the .38 bullet leaves the cylinder. This maybe your problem. It's very hard to clean this out and this is why it's jamming, at least with my gun!
    As an aside - those "rings around the chamber" clean up nicely with a bit of scotchbrite pad wrapped around a rod or dowel or something. Swab the chamber with some solvent first, let it sit a few minutes, and run the scotchbrite pad in. It doesn't have to be all that tight or anything, and it will scrub that ring right down.

    This also works nicely on the carbon rings on the front face of the cylinder...but it can also take some bluing with it, depending on the gun.
    S&W M&P 45; Ruger GP100 .357 Magnum; Charter Arms .38 Undercover
    http://www.usacarry.com/forums/members/phillip-gain-albums-phil-s-photos-picture3828-reciprocity-map-29jun11.JPG

  10. #10
    Quote Originally Posted by BKG203 View Post
    I think I am going to contact S&W and talk to a rep. Thanks for all the responses and suggestions from everyone.
    Their customer service is really good. My M&P 45 had an inoperative trigger when I first bought it. Even though it was a used gun, they replaced the entire trigger and sear assembly (which I suspect may have been aftermarket and improperly installed by an amateur) , cleaned it nicely, and sent an extra magazine back along with it. Turn time was maybe 2 weeks. And they didn't charge me a dime!
    S&W M&P 45; Ruger GP100 .357 Magnum; Charter Arms .38 Undercover
    http://www.usacarry.com/forums/members/phillip-gain-albums-phil-s-photos-picture3828-reciprocity-map-29jun11.JPG

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •