M14 - M1A Rifles
Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: M14 - M1A Rifles

  1. #1

    Thumbs up M14 - M1A Rifles

    Iíve thought about writing on this subject for a while. In searching their history I found several good articles through out the net so I wonít take too much time with that. Letís suffice it to say that everything started with John C. Garand and his celebrated M1 rifle. Post WWII there were requests for improvement. For the most part more ammunition capacity and a detachable magazine was wanted. The question was how to do it. Once again they turned to Mr. Garand. He gave them his initial drawings but in them the rifle was still chambered in .30-06 and that wasnít what was really wanted by the time said drawings arrived. You see, one of the other men on the project was working on a new ammunition based on the .30-06 but shorter, lighter (some what) but performed almost identically to the .30-06. Of course that was the 7.62◊51 NATO or the .308 Win.

    When examining the action there was very little that needed to be changed. The trigger guard needed to be opened up for the magazine and a retention system added. Not that difficult. Make the magazine rock into place so there is a place for it to be held front and rear. Little need be done to the receiver for that to happen. Minor changes in the original machining process and you have it.

    We can always use a higher rate of fire in a battle rifle. Thatís a given. So we have the first major change in the rifle. On the exposed right locking lug they simply added a steel roller. Keep it lubed and it will serve you well. Since we took the metal to metal friction out of the picture on this side the action is much cycles faster.

    There was a function on the M14 that doesnít exist on the civilian version. That is the selection knob. Sure you still had the same safety lever as the M1. The trigger mech still functioned the same as the M1. But now with the M14 on the back of the receiver we have a knob that by turning to one setting or the other one can choose between the M1ís semi-auto and the new full auto. This effectively gave us the worlds only battle rifle that dueled as a squad automatic weapon. Of course for the civilian market this feature was never added.

    These are fantastic rifles that just never quit. Theyíre built tough as a tank. Iíve worked with ones that had seen action in Vietnam, therefore having the full auto knob, That still shot remarkably well. With a good shock bedding job these rifles are still used as sniper/ dedicated marksman rifles. Theyíre great for shots up to 800 meters depending on the quality of the bedding job and the person behind the trigger. Iíve watched Marine Scout Snipers with these rifles make up to 1000 meter shots with these accurately. Of course at that range you are trying for minute of human not head shots.

    Thereís enough room in the receivers of the M1, M14, M1A to take a beating and keep on ticking. They were a favorite of service men in Vietnam. When other rifles just wouldnít work the M14 just kept going and actually saved lives because it was often the only rifle still running in the squad but thatís a story for another day.

    Naturally a clean rifle is a happy rifle. Everyone that will ever come in contact with this article will already know that. So I wonít go on about that. One thing I to want to discuss is lube. From the days of the M1 Garand these rifles were designed to run with grease. The biggest place for this is the Operation Rod Spring. The easiest way to apply it is to put a liberal glob on the op rod where the spring enters it. Then slowly spin the spring through the grease until it is fully seated. Clear the excess away and use it elsewhere.

    These rifles are built so well there is little that goes wrong with them. It would be a good idea to keep a couple Op Rod Springs on hand. This will be the first thing to wear out and when it does it caused problems throughout the action. You see it is this spring that closes the action after itís been fired or upon loading. If this spring doesnít have enough strength the action wont close all the way, the action is disconnected, and will not fire. That spring is everything. One other to keep things flowing nicely is the extractor spring. They rarely wear out but cause problems when they do. A replacement is a good idea.

    Keep it clean, including the piston (no oil or grease on the piston ever). A bronze brush is the easiest way to keep the piston alive and well.

    Ok, weíre done here. You are now all but experts on the M1 down to the M1A. Hope you enjoyed the article and found it informative.

  2.   
  3. #2
    good article. never thought to grease the spring and oprod, i will take care of that the next day im home. ive found that the food grade grease works wonderfully on my M1A. It will withstand enormous amounts of heat and picks up very little dirt and 1 tube will last a lifetime. thanks for taking the time to post that

  4. #3
    Glad you enjoyed it.

  5. #4
    Great read on a great rifle. Thanks man.
    "There is no consitutional right to be protected by the state against being murdered by criminals or madmen." (7th Cir. 1982, Bowers v. DeVito)Stay safe, and stay trained.www.sazsatt.com

  6. #5
    appreciate it.

  7. #6
    Join Date
    Sep 2007
    Location
    Gray Court, SC
    Posts
    2,934
    Great post! I love my M1's and my M1A. I'm getting ready to build a M1 in 308 if my barrel gets here. It went backorder so I may have to order another one from somewhere else.
    USAF Retired, CATM, SC CWP, NH NR CWP, NRA Benefactor
    To preserve liberty, it is essential that the whole body of people always possess arms, and be taught alike, especially when young, how to use them... -- Richard Henry Lee, 1787

  8. #7
    Dont forget to add some pictures when you do.

  9. #8
    Join Date
    Sep 2007
    Location
    Gray Court, SC
    Posts
    2,934
    I will.
    USAF Retired, CATM, SC CWP, NH NR CWP, NRA Benefactor
    To preserve liberty, it is essential that the whole body of people always possess arms, and be taught alike, especially when young, how to use them... -- Richard Henry Lee, 1787

  10. #9
    Yes Sir, Good Read.. Great Rifle...
    ~
    They were a favorite of service men in Vietnam. When other rifles just wouldnít work the M14 just kept going~

    I laugh now, but when the Armory in Da Nang said we had to turn in our 14's and get the New M-16, I was Pis$_d... I thought the 16 was made by Mattel... The 16's rattled, and did not have that nice rifle "Crack" sound. I guess I am still a fan of the Heavy Wood Rifle...
    Semper Fi

  11. #10
    Thanks for reading and thanks for your service.

Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Quantcast